Petro Mold Co.

This unique corner store has the Pharmacy on one side and a Soda Fountain on the other.  Although the days of the Soda Jerk are long gone, you can re-live history right here.

Mold # 1932 - Pharmacy and Soda Fountain - $69.98
 

Technique                 Colors and supplies by:  

SS-2     Lemon Meringue           SS-135 White                            TL-101 Brandied Raspberry
SS-23   Mink                             SS-138 Flat Black                      TL-113 Hyacinth Blue
SS-32   Razzberri                       SS-176 Christmas Red               TL-116 White Cloud
SS-80   Glorious Gold                 SS-337 Dark Blue                      TL-125 Sunflower
SS-81   Shimmering Silver          SS-373 Brick Red                      TL-134 Black Forest
SS-84   Copper                          SS-377 Hunter Green                AC-516 Porcelain Mist
SS-108  Light Gray                    TL-4     Black                           AC-520 Solvent
SS-130  Medium Gray                TL-23   Golden Toffee

 General Directions: Begin with properly cleaned and fired 06 bisque.  Thin down White and apply over entire piece to get into all detail.  When dry, apply another smooth coat of undiluted White.  Allow to dry.  Apply Hyacinth Blue in small areas wiping back for highlights until entire piece is covered.  Dampen a soft cloth with Solvent to wipe back further highlights and an overall even look to antiquing.  Spray with Porcelain Mist to set TL.  Reminder: In this technique, sometimes more than 1 coat of TL is necessary so between each coat, the color must be sprayed in order not to lift the first layer.  Refer to photo for color placements in various sections. 

 Technique

1.       Apply Black TL to the cobblestones, sidewalk, roof and the underside of the front rounded corner.  Wipe back, except underside of front corner, then spray.  Randomly drybrush cobblestones with Mink, Brick Red and Light Gray.  Lightly drybrush sidewalk with Medium Gray then tip into White to very lightly highlight.

2.       Use 3 coats of White Cloud for bricks of building spraying between each layer.  If needed, evenly drybrush with White to achieve a solid color being careful not to lose the shadows around windows and doors.

3.       For the trim and doors, apply 2 coats of Golden Toffee.  Use Sunflower for the signs.  Paint lettering Christmas Red and detail lines with Flat Black.  Lightly highlight these areas with Lemon Meringue. 

4.       Apply 2 coats of Hyacinth Blue to first floor window trims and second floor window above door.  Drybrush with Dark Blue then tip into White to lightly highlight.

5.       Use Black Forest on all second floor window trims, gable ends and alternating awning stripes.  Spray.  Refer to photo for placements.  Drybrush with Hunter Green then tip into White to lightly highlight.

6.       For the remaining awning stripes and all window frames, apply Brandied Raspberry.  Spray.  Lightly drybrush with Razzberri then tip into White to lightly highlight.

7.       Paint the kick plates and doorknobs Flat Black.  Spray entire piece.  Heavily drybrush underside of front corner and top with Copper.  On green window trims detail with Glorious Gold; also drybrush highlights to underside of front corner.  Lightly drybrush kick plates and door knobs with Shimmering Silver.  Paint doorknobs, detail of corners on front windows and blue window trims Copper.

[Home] 

Contact Us Toll Free - US / Canada:  888-811-6653

Send email to petro@velocity.net with questions or comments about this web site.
Copyright © 1996-2010 Petro Mold Co.
Last modified: August 11, 2010